Getting the right limit strap length is critical — too short and you limit your suspension travel prematurely; too long and the strap won't engage before something breaks. This guide walks you through how to measure correctly and use our length charts to order the right straps the first time.
How to Measure
You'll need a tape measure, a jack, and jack stands. Here's the step-by-step:
- Support the vehicle on jack stands with the suspension hanging at full droop (wheels hanging down as far as they'll go)
- Identify your two mounting points: one on the frame, one on the axle or control arm
- Measure the straight-line distance between the center of each mounting hole
- Add 1–2 inches of "pre-load" — the strap should be slightly shorter than your measured distance so it's already under light tension at full droop
- Order straps at that length, or round to the nearest half-inch if using custom manufacturer like Bull Strap
💡 Tip
Measure at full droop, not at rest. Your suspension geometry changes dramatically through its travel, and you want to size for the worst-case (maximum droop) position.
Limit Strap Length Chart by Vehicle
Jeep Wrangler TJ (1997–2006)
| Lift Height | Front Strap Length | Rear Strap Length |
|---|---|---|
| 2–3" | 10–12" | 12–14" |
| 3–4" | 12–14" | 14–16" |
| 4–5" | 14–16" | 16–18" |
| 6"+ | Custom | Custom |
Jeep Wrangler JK (2007–2018)
| Lift Height | Front Strap Length | Rear Strap Length |
|---|---|---|
| 2.5" | 12–14" | 14–16" |
| 3.5" | 14–16" | 16–18" |
| 4.5" | 16–18" | 18–20" |
| 6"+ | Custom | Custom |
Jeep Wrangler JL (2018–Present)
| Lift Height | Front Strap Length | Rear Strap Length |
|---|---|---|
| 2.5" | 14–16" | 16–18" |
| 3.5" | 16–18" | 18–20" |
| 4.5" | 18–20" | 20–22" |
| 6"+ | Custom | Custom |
Toyota Tacoma (2005–Present)
| Lift Height | Front Strap Length | Rear Strap Length |
|---|---|---|
| 2–3" | 10–12" | 14–16" |
| 3–4" | 12–14" | 16–18" |
| 4"+ | Custom | Custom |
Toyota 4Runner (2003–Present)
| Lift Height | Front Strap Length | Rear Strap Length |
|---|---|---|
| 2–3" | 10–12" | 12–14" |
| 3–4" | 12–14" | 14–16" |
| 4"+ | Custom | Custom |
Ford F-150 (2015–Present)
| Lift Height | Front Strap Length | Rear Strap Length |
|---|---|---|
| 2–3" | 12–14" | 14–16" |
| 3–4" | 14–16" | 16–18" |
| 4"+ | Custom | Custom |
⚠️ Important
These are general guidelines. Your actual length depends on your specific shock length, control arm geometry, and mounting point locations. Always measure your vehicle at full droop for the most accurate size. For custom lengths, Bull Strap can manufacture to your exact specification.
Strap Width & Material Comparison
Width
1" straps: Light-duty, suitable for small UTVs and light duty use. Not recommended for full-size trucks or heavy rigs.
1.5" straps: Good middle ground for Jeeps and smaller trucks. Handles most off-road use.
2" straps: Recommended for full-size trucks, heavy rigs, and racing applications. Maximum load distribution and durability.
Material Types
| Material | Strength | UV Resistance | Best Use | Price |
|---|---|---|---|---|
| Military-spec nylon (Bull Strap) | Highest | Excellent | Racing, heavy use | $$$ |
| Heavy-duty nylon | High | Good | Off-road, lifted vehicles | $$ |
| Polyester | Medium | Good | Budget builds | $ |
| Polypropylene | Low | Fair | Temporary use only | $ |
End Configurations
Sewn loops: Most common. One or both ends have a sewn loop that accepts a bolt. Simple and reliable.
Clevis ends: Fork-style ends that clip into a receiver. Quick removal option.
Bolt-through: Flat end designed to bolt directly between two existing mount points.
Our Recommendation
For most off-road builds, a 2" military-spec nylon strap (like Bull Strap) with sewn loop ends is the best choice. It's strong enough for any trail or race application, UV and weather resistant, and will outlast your vehicle. For custom lengths, Bull Strap's Made in USA manufacturing is the industry standard — order direct from their website.
Check Price on Amazon →